| [e16e8f2] | 1 | /* |
|---|
| 2 | * i82365.h 1.15 1999/10/25 20:03:34 |
|---|
| 3 | * |
|---|
| 4 | * The contents of this file may be used under the |
|---|
| 5 | * terms of the GNU General Public License version 2 (the "GPL"). |
|---|
| 6 | * |
|---|
| 7 | * Software distributed under the License is distributed on an "AS IS" |
|---|
| 8 | * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See |
|---|
| 9 | * the License for the specific language governing rights and |
|---|
| 10 | * limitations under the License. |
|---|
| 11 | * |
|---|
| 12 | * The initial developer of the original code is David A. Hinds |
|---|
| 13 | * <dahinds@users.sourceforge.net>. Portions created by David A. Hinds |
|---|
| 14 | * are Copyright (C) 1999 David A. Hinds. All Rights Reserved. |
|---|
| 15 | */ |
|---|
| 16 | |
|---|
| 17 | #ifndef _LINUX_I82365_H |
|---|
| 18 | #define _LINUX_I82365_H |
|---|
| 19 | |
|---|
| 20 | /* register definitions for the Intel 82365SL PCMCIA controller */ |
|---|
| 21 | |
|---|
| 22 | /* Offsets for PCIC registers */ |
|---|
| 23 | #define I365_IDENT 0x00 /* Identification and revision */ |
|---|
| 24 | #define I365_STATUS 0x01 /* Interface status */ |
|---|
| 25 | #define I365_POWER 0x02 /* Power and RESETDRV control */ |
|---|
| 26 | #define I365_INTCTL 0x03 /* Interrupt and general control */ |
|---|
| 27 | #define I365_CSC 0x04 /* Card status change */ |
|---|
| 28 | #define I365_CSCINT 0x05 /* Card status change interrupt control */ |
|---|
| 29 | #define I365_ADDRWIN 0x06 /* Address window enable */ |
|---|
| 30 | #define I365_IOCTL 0x07 /* I/O control */ |
|---|
| 31 | #define I365_GENCTL 0x16 /* Card detect and general control */ |
|---|
| 32 | #define I365_GBLCTL 0x1E /* Global control register */ |
|---|
| 33 | |
|---|
| 34 | /* Offsets for I/O and memory window registers */ |
|---|
| 35 | #define I365_IO(map) (0x08+((map)<<2)) |
|---|
| 36 | #define I365_MEM(map) (0x10+((map)<<3)) |
|---|
| 37 | #define I365_W_START 0 |
|---|
| 38 | #define I365_W_STOP 2 |
|---|
| 39 | #define I365_W_OFF 4 |
|---|
| 40 | |
|---|
| 41 | /* Flags for I365_STATUS */ |
|---|
| 42 | #define I365_CS_BVD1 0x01 |
|---|
| 43 | #define I365_CS_STSCHG 0x01 |
|---|
| 44 | #define I365_CS_BVD2 0x02 |
|---|
| 45 | #define I365_CS_SPKR 0x02 |
|---|
| 46 | #define I365_CS_DETECT 0x0C |
|---|
| 47 | #define I365_CS_WRPROT 0x10 |
|---|
| 48 | #define I365_CS_READY 0x20 /* Inverted */ |
|---|
| 49 | #define I365_CS_POWERON 0x40 |
|---|
| 50 | #define I365_CS_GPI 0x80 |
|---|
| 51 | |
|---|
| 52 | /* Flags for I365_POWER */ |
|---|
| 53 | #define I365_PWR_OFF 0x00 /* Turn off the socket */ |
|---|
| 54 | #define I365_PWR_OUT 0x80 /* Output enable */ |
|---|
| 55 | #define I365_PWR_NORESET 0x40 /* Disable RESETDRV on resume */ |
|---|
| 56 | #define I365_PWR_AUTO 0x20 /* Auto pwr switch enable */ |
|---|
| 57 | #define I365_VCC_MASK 0x18 /* Mask for turning off Vcc */ |
|---|
| 58 | /* There are different layouts for B-step and DF-step chips: the B |
|---|
| 59 | step has independent Vpp1/Vpp2 control, and the DF step has only |
|---|
| 60 | Vpp1 control, plus 3V control */ |
|---|
| 61 | #define I365_VCC_5V 0x10 /* Vcc = 5.0v */ |
|---|
| 62 | #define I365_VCC_3V 0x18 /* Vcc = 3.3v */ |
|---|
| 63 | #define I365_VPP2_MASK 0x0c /* Mask for turning off Vpp2 */ |
|---|
| 64 | #define I365_VPP2_5V 0x04 /* Vpp2 = 5.0v */ |
|---|
| 65 | #define I365_VPP2_12V 0x08 /* Vpp2 = 12.0v */ |
|---|
| 66 | #define I365_VPP1_MASK 0x03 /* Mask for turning off Vpp1 */ |
|---|
| 67 | #define I365_VPP1_5V 0x01 /* Vpp2 = 5.0v */ |
|---|
| 68 | #define I365_VPP1_12V 0x02 /* Vpp2 = 12.0v */ |
|---|
| 69 | |
|---|
| 70 | /* Flags for I365_INTCTL */ |
|---|
| 71 | #define I365_RING_ENA 0x80 |
|---|
| 72 | #define I365_PC_RESET 0x40 |
|---|
| 73 | #define I365_PC_IOCARD 0x20 |
|---|
| 74 | #define I365_INTR_ENA 0x10 |
|---|
| 75 | #define I365_IRQ_MASK 0x0F |
|---|
| 76 | |
|---|
| 77 | /* Flags for I365_CSC and I365_CSCINT*/ |
|---|
| 78 | #define I365_CSC_BVD1 0x01 |
|---|
| 79 | #define I365_CSC_STSCHG 0x01 |
|---|
| 80 | #define I365_CSC_BVD2 0x02 |
|---|
| 81 | #define I365_CSC_READY 0x04 |
|---|
| 82 | #define I365_CSC_DETECT 0x08 |
|---|
| 83 | #define I365_CSC_ANY 0x0F |
|---|
| 84 | #define I365_CSC_GPI 0x10 |
|---|
| 85 | |
|---|
| 86 | /* Flags for I365_ADDRWIN */ |
|---|
| 87 | #define I365_ENA_IO(map) (0x40 << (map)) |
|---|
| 88 | #define I365_ENA_MEM(map) (0x01 << (map)) |
|---|
| 89 | |
|---|
| 90 | /* Flags for I365_IOCTL */ |
|---|
| 91 | #define I365_IOCTL_MASK(map) (0x0F << (map<<2)) |
|---|
| 92 | #define I365_IOCTL_WAIT(map) (0x08 << (map<<2)) |
|---|
| 93 | #define I365_IOCTL_0WS(map) (0x04 << (map<<2)) |
|---|
| 94 | #define I365_IOCTL_IOCS16(map) (0x02 << (map<<2)) |
|---|
| 95 | #define I365_IOCTL_16BIT(map) (0x01 << (map<<2)) |
|---|
| 96 | |
|---|
| 97 | /* Flags for I365_GENCTL */ |
|---|
| 98 | #define I365_CTL_16DELAY 0x01 |
|---|
| 99 | #define I365_CTL_RESET 0x02 |
|---|
| 100 | #define I365_CTL_GPI_ENA 0x04 |
|---|
| 101 | #define I365_CTL_GPI_CTL 0x08 |
|---|
| 102 | #define I365_CTL_RESUME 0x10 |
|---|
| 103 | #define I365_CTL_SW_IRQ 0x20 |
|---|
| 104 | |
|---|
| 105 | /* Flags for I365_GBLCTL */ |
|---|
| 106 | #define I365_GBL_PWRDOWN 0x01 |
|---|
| 107 | #define I365_GBL_CSC_LEV 0x02 |
|---|
| 108 | #define I365_GBL_WRBACK 0x04 |
|---|
| 109 | #define I365_GBL_IRQ_0_LEV 0x08 |
|---|
| 110 | #define I365_GBL_IRQ_1_LEV 0x10 |
|---|
| 111 | |
|---|
| 112 | /* Flags for memory window registers */ |
|---|
| 113 | #define I365_MEM_16BIT 0x8000 /* In memory start high byte */ |
|---|
| 114 | #define I365_MEM_0WS 0x4000 |
|---|
| 115 | #define I365_MEM_WS1 0x8000 /* In memory stop high byte */ |
|---|
| 116 | #define I365_MEM_WS0 0x4000 |
|---|
| 117 | #define I365_MEM_WRPROT 0x8000 /* In offset high byte */ |
|---|
| 118 | #define I365_MEM_REG 0x4000 |
|---|
| 119 | |
|---|
| 120 | #define I365_REG(slot, reg) (((slot) << 6) + reg) |
|---|
| 121 | |
|---|
| 122 | #endif /* _LINUX_I82365_H */ |
|---|
| 123 | |
|---|
| 124 | //***************************************************************************** |
|---|
| 125 | //***************************************************************************** |
|---|
| 126 | //***************************************************************************** |
|---|
| 127 | //***************************************************************************** |
|---|
| 128 | //***************************************************************************** |
|---|
| 129 | // Beginning vg468.h (for VADEM chipset) |
|---|
| 130 | |
|---|
| 131 | #ifndef _LINUX_VG468_H |
|---|
| 132 | #define _LINUX_VG468_H |
|---|
| 133 | |
|---|
| 134 | /* Special bit in I365_IDENT used for Vadem chip detection */ |
|---|
| 135 | #define I365_IDENT_VADEM 0x08 |
|---|
| 136 | |
|---|
| 137 | /* Special definitions in I365_POWER */ |
|---|
| 138 | #define VG468_VPP2_MASK 0x0c |
|---|
| 139 | #define VG468_VPP2_5V 0x04 |
|---|
| 140 | #define VG468_VPP2_12V 0x08 |
|---|
| 141 | |
|---|
| 142 | /* Unique Vadem registers */ |
|---|
| 143 | #define VG469_VSENSE 0x1f /* Card voltage sense */ |
|---|
| 144 | #define VG469_VSELECT 0x2f /* Card voltage select */ |
|---|
| 145 | #define VG468_CTL 0x38 /* Control register */ |
|---|
| 146 | #define VG468_TIMER 0x39 /* Timer control */ |
|---|
| 147 | #define VG468_MISC 0x3a /* Miscellaneous */ |
|---|
| 148 | #define VG468_GPIO_CFG 0x3b /* GPIO configuration */ |
|---|
| 149 | #define VG469_EXT_MODE 0x3c /* Extended mode register */ |
|---|
| 150 | #define VG468_SELECT 0x3d /* Programmable chip select */ |
|---|
| 151 | #define VG468_SELECT_CFG 0x3e /* Chip select configuration */ |
|---|
| 152 | #define VG468_ATA 0x3f /* ATA control */ |
|---|
| 153 | |
|---|
| 154 | /* Flags for VG469_VSENSE */ |
|---|
| 155 | #define VG469_VSENSE_A_VS1 0x01 |
|---|
| 156 | #define VG469_VSENSE_A_VS2 0x02 |
|---|
| 157 | #define VG469_VSENSE_B_VS1 0x04 |
|---|
| 158 | #define VG469_VSENSE_B_VS2 0x08 |
|---|
| 159 | |
|---|
| 160 | /* Flags for VG469_VSELECT */ |
|---|
| 161 | #define VG469_VSEL_VCC 0x03 |
|---|
| 162 | #define VG469_VSEL_5V 0x00 |
|---|
| 163 | #define VG469_VSEL_3V 0x03 |
|---|
| 164 | #define VG469_VSEL_MAX 0x0c |
|---|
| 165 | #define VG469_VSEL_EXT_STAT 0x10 |
|---|
| 166 | #define VG469_VSEL_EXT_BUS 0x20 |
|---|
| 167 | #define VG469_VSEL_MIXED 0x40 |
|---|
| 168 | #define VG469_VSEL_ISA 0x80 |
|---|
| 169 | |
|---|
| 170 | /* Flags for VG468_CTL */ |
|---|
| 171 | #define VG468_CTL_SLOW 0x01 /* 600ns memory timing */ |
|---|
| 172 | #define VG468_CTL_ASYNC 0x02 /* Asynchronous bus clocking */ |
|---|
| 173 | #define VG468_CTL_TSSI 0x08 /* Tri-state some outputs */ |
|---|
| 174 | #define VG468_CTL_DELAY 0x10 /* Card detect debounce */ |
|---|
| 175 | #define VG468_CTL_INPACK 0x20 /* Obey INPACK signal? */ |
|---|
| 176 | #define VG468_CTL_POLARITY 0x40 /* VCCEN polarity */ |
|---|
| 177 | #define VG468_CTL_COMPAT 0x80 /* Compatibility stuff */ |
|---|
| 178 | |
|---|
| 179 | #define VG469_CTL_WS_COMPAT 0x04 /* Wait state compatibility */ |
|---|
| 180 | #define VG469_CTL_STRETCH 0x10 /* LED stretch */ |
|---|
| 181 | |
|---|
| 182 | /* Flags for VG468_TIMER */ |
|---|
| 183 | #define VG468_TIMER_ZEROPWR 0x10 /* Zero power control */ |
|---|
| 184 | #define VG468_TIMER_SIGEN 0x20 /* Power up */ |
|---|
| 185 | #define VG468_TIMER_STATUS 0x40 /* Activity timer status */ |
|---|
| 186 | #define VG468_TIMER_RES 0x80 /* Timer resolution */ |
|---|
| 187 | #define VG468_TIMER_MASK 0x0f /* Activity timer timeout */ |
|---|
| 188 | |
|---|
| 189 | /* Flags for VG468_MISC */ |
|---|
| 190 | #define VG468_MISC_GPIO 0x04 /* General-purpose IO */ |
|---|
| 191 | #define VG468_MISC_DMAWSB 0x08 /* DMA wait state control */ |
|---|
| 192 | #define VG469_MISC_LEDENA 0x10 /* LED enable */ |
|---|
| 193 | #define VG468_MISC_VADEMREV 0x40 /* Vadem revision control */ |
|---|
| 194 | #define VG468_MISC_UNLOCK 0x80 /* Unique register lock */ |
|---|
| 195 | |
|---|
| 196 | /* Flags for VG469_EXT_MODE_A */ |
|---|
| 197 | #define VG469_MODE_VPPST 0x03 /* Vpp steering control */ |
|---|
| 198 | #define VG469_MODE_INT_SENSE 0x04 /* Internal voltage sense */ |
|---|
| 199 | #define VG469_MODE_CABLE 0x08 |
|---|
| 200 | #define VG469_MODE_COMPAT 0x10 /* i82365sl B or DF step */ |
|---|
| 201 | #define VG469_MODE_TEST 0x20 |
|---|
| 202 | #define VG469_MODE_RIO 0x40 /* Steer RIO to INTR? */ |
|---|
| 203 | |
|---|
| 204 | /* Flags for VG469_EXT_MODE_B */ |
|---|
| 205 | #define VG469_MODE_B_3V 0x01 /* 3.3v for socket B */ |
|---|
| 206 | |
|---|
| 207 | #endif /* _LINUX_VG468_H */ |
|---|
| 208 | |
|---|
| 209 | |
|---|
| 210 | //***************************************************************************** |
|---|
| 211 | //***************************************************************************** |
|---|
| 212 | //***************************************************************************** |
|---|
| 213 | //***************************************************************************** |
|---|
| 214 | //***************************************************************************** |
|---|
| 215 | // Beginning ricoh.h (RICOH chipsets) |
|---|
| 216 | |
|---|
| 217 | #ifndef _LINUX_RICOH_H |
|---|
| 218 | #define _LINUX_RICOH_H |
|---|
| 219 | |
|---|
| 220 | |
|---|
| 221 | #define RF5C_MODE_CTL 0x1f /* Mode control */ |
|---|
| 222 | #define RF5C_PWR_CTL 0x2f /* Mixed voltage control */ |
|---|
| 223 | #define RF5C_CHIP_ID 0x3a /* Chip identification */ |
|---|
| 224 | #define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */ |
|---|
| 225 | |
|---|
| 226 | /* I/O window address offset */ |
|---|
| 227 | #define RF5C_IO_OFF(w) (0x36+((w)<<1)) |
|---|
| 228 | |
|---|
| 229 | /* Flags for RF5C_MODE_CTL */ |
|---|
| 230 | #define RF5C_MODE_ATA 0x01 /* ATA mode */ |
|---|
| 231 | #define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */ |
|---|
| 232 | #define RF5C_MODE_CA21 0x04 |
|---|
| 233 | #define RF5C_MODE_CA22 0x08 |
|---|
| 234 | #define RF5C_MODE_CA23 0x10 |
|---|
| 235 | #define RF5C_MODE_CA24 0x20 |
|---|
| 236 | #define RF5C_MODE_CA25 0x40 |
|---|
| 237 | #define RF5C_MODE_3STATE_BIT7 0x80 |
|---|
| 238 | |
|---|
| 239 | /* Flags for RF5C_PWR_CTL */ |
|---|
| 240 | #define RF5C_PWR_VCC_3V 0x01 |
|---|
| 241 | #define RF5C_PWR_IREQ_HIGH 0x02 |
|---|
| 242 | #define RF5C_PWR_INPACK_ENA 0x04 |
|---|
| 243 | #define RF5C_PWR_5V_DET 0x08 |
|---|
| 244 | #define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */ |
|---|
| 245 | #define RF5C_PWR_DREQ_LOW 0x20 |
|---|
| 246 | #define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */ |
|---|
| 247 | #define RF5C_PWR_DREQ_INPACK 0x40 |
|---|
| 248 | #define RF5C_PWR_DREQ_SPKR 0x80 |
|---|
| 249 | #define RF5C_PWR_DREQ_IOIS16 0xc0 |
|---|
| 250 | |
|---|
| 251 | /* Values for RF5C_CHIP_ID */ |
|---|
| 252 | #define RF5C_CHIP_RF5C296 0x32 |
|---|
| 253 | #define RF5C_CHIP_RF5C396 0xb2 |
|---|
| 254 | |
|---|
| 255 | /* Flags for RF5C_MODE_CTL_3 */ |
|---|
| 256 | #define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */ |
|---|
| 257 | #define RF5C_MCTL3_DMA_ENA 0x02 |
|---|
| 258 | |
|---|
| 259 | /* Register definitions for Ricoh PCI-to-CardBus bridges */ |
|---|
| 260 | |
|---|
| 261 | /* Extra bits in CB_BRIDGE_CONTROL */ |
|---|
| 262 | #define RL5C46X_BCR_3E0_ENA 0x0800 |
|---|
| 263 | #define RL5C46X_BCR_3E2_ENA 0x1000 |
|---|
| 264 | |
|---|
| 265 | /* Bridge Configuration Register */ |
|---|
| 266 | #define RL5C4XX_CONFIG 0x80 /* 16 bit */ |
|---|
| 267 | #define RL5C4XX_CONFIG_IO_1_MODE 0x0200 |
|---|
| 268 | #define RL5C4XX_CONFIG_IO_0_MODE 0x0100 |
|---|
| 269 | #define RL5C4XX_CONFIG_PREFETCH 0x0001 |
|---|
| 270 | |
|---|
| 271 | |
|---|
| 272 | /* Misc Control Register */ |
|---|
| 273 | #define RL5C4XX_MISC 0x0082 /* 16 bit */ |
|---|
| 274 | #define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002 |
|---|
| 275 | #define RL5C4XX_MISC_VCCEN_POL 0x0100 |
|---|
| 276 | #define RL5C4XX_MISC_VPPEN_POL 0x0200 |
|---|
| 277 | #define RL5C46X_MISC_SUSPEND 0x0001 |
|---|
| 278 | #define RL5C46X_MISC_PWR_SAVE_2 0x0004 |
|---|
| 279 | #define RL5C46X_MISC_IFACE_BUSY 0x0008 |
|---|
| 280 | #define RL5C46X_MISC_B_LOCK 0x0010 |
|---|
| 281 | #define RL5C46X_MISC_A_LOCK 0x0020 |
|---|
| 282 | #define RL5C46X_MISC_PCI_LOCK 0x0040 |
|---|
| 283 | #define RL5C47X_MISC_IFACE_BUSY 0x0004 |
|---|
| 284 | #define RL5C47X_MISC_PCI_INT_MASK 0x0018 |
|---|
| 285 | #define RL5C47X_MISC_PCI_INT_DIS 0x0020 |
|---|
| 286 | #define RL5C47X_MISC_SUBSYS_WR 0x0040 |
|---|
| 287 | #define RL5C47X_MISC_SRIRQ_ENA 0x0080 |
|---|
| 288 | #define RL5C47X_MISC_5V_DISABLE 0x0400 |
|---|
| 289 | #define RL5C47X_MISC_LED_POL 0x0800 |
|---|
| 290 | |
|---|
| 291 | /* 16-bit Interface Control Register */ |
|---|
| 292 | #define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */ |
|---|
| 293 | #define RL5C4XX_16CTL_IO_TIMING 0x0100 |
|---|
| 294 | #define RL5C4XX_16CTL_MEM_TIMING 0x0200 |
|---|
| 295 | #define RL5C46X_16CTL_LEVEL_1 0x0010 |
|---|
| 296 | #define RL5C46X_16CTL_LEVEL_2 0x0020 |
|---|
| 297 | |
|---|
| 298 | /* 16-bit IO and memory timing registers */ |
|---|
| 299 | #define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */ |
|---|
| 300 | #define RL5C4XX_16BIT_MEM_0 0x0088 /* 16 bit */ |
|---|
| 301 | #define RL5C4XX_SETUP_MASK 0x0007 |
|---|
| 302 | #define RL5C4XX_SETUP_SHIFT 0 |
|---|
| 303 | #define RL5C4XX_CMD_MASK 0x01f0 |
|---|
| 304 | #define RL5C4XX_CMD_SHIFT 4 |
|---|
| 305 | #define RL5C4XX_HOLD_MASK 0x1c00 |
|---|
| 306 | #define RL5C4XX_HOLD_SHIFT 10 |
|---|
| 307 | #define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */ |
|---|
| 308 | #define RL5C4XX_ZV_ENABLE 0x08 |
|---|
| 309 | |
|---|
| 310 | #endif /* _LINUX_RICOH_H */ |
|---|
| 311 | |
|---|
| 312 | |
|---|
| 313 | //***************************************************************************** |
|---|
| 314 | //***************************************************************************** |
|---|
| 315 | //***************************************************************************** |
|---|
| 316 | //***************************************************************************** |
|---|
| 317 | //***************************************************************************** |
|---|
| 318 | // Beginning cirrus.h (CIRRUS chipsets) |
|---|
| 319 | |
|---|
| 320 | #ifndef _LINUX_CIRRUS_H |
|---|
| 321 | #define _LINUX_CIRRUS_H |
|---|
| 322 | |
|---|
| 323 | #ifndef PCI_VENDOR_ID_CIRRUS |
|---|
| 324 | #define PCI_VENDOR_ID_CIRRUS 0x1013 |
|---|
| 325 | #endif |
|---|
| 326 | #ifndef PCI_DEVICE_ID_CIRRUS_6729 |
|---|
| 327 | #define PCI_DEVICE_ID_CIRRUS_6729 0x1100 |
|---|
| 328 | #endif |
|---|
| 329 | #ifndef PCI_DEVICE_ID_CIRRUS_6832 |
|---|
| 330 | #define PCI_DEVICE_ID_CIRRUS_6832 0x1110 |
|---|
| 331 | #endif |
|---|
| 332 | |
|---|
| 333 | #define PD67_MISC_CTL_1 0x16 /* Misc control 1 */ |
|---|
| 334 | #define PD67_FIFO_CTL 0x17 /* FIFO control */ |
|---|
| 335 | #define PD67_MISC_CTL_2 0x1E /* Misc control 2 */ |
|---|
| 336 | #define PD67_CHIP_INFO 0x1f /* Chip information */ |
|---|
| 337 | #define PD67_ATA_CTL 0x026 /* 6730: ATA control */ |
|---|
| 338 | #define PD67_EXT_INDEX 0x2e /* Extension index */ |
|---|
| 339 | #define PD67_EXT_DATA 0x2f /* Extension data */ |
|---|
| 340 | |
|---|
| 341 | /* PD6722 extension registers -- indexed in PD67_EXT_INDEX */ |
|---|
| 342 | #define PD67_DATA_MASK0 0x01 /* Data mask 0 */ |
|---|
| 343 | #define PD67_DATA_MASK1 0x02 /* Data mask 1 */ |
|---|
| 344 | #define PD67_DMA_CTL 0x03 /* DMA control */ |
|---|
| 345 | |
|---|
| 346 | /* PD6730 extension registers -- indexed in PD67_EXT_INDEX */ |
|---|
| 347 | #define PD67_EXT_CTL_1 0x03 /* Extension control 1 */ |
|---|
| 348 | #define PD67_MEM_PAGE(n) ((n)+5) /* PCI window bits 31:24 */ |
|---|
| 349 | #define PD67_EXTERN_DATA 0x0a |
|---|
| 350 | #define PD67_MISC_CTL_3 0x25 |
|---|
| 351 | #define PD67_SMB_PWR_CTL 0x26 |
|---|
| 352 | |
|---|
| 353 | /* I/O window address offset */ |
|---|
| 354 | #define PD67_IO_OFF(w) (0x36+((w)<<1)) |
|---|
| 355 | |
|---|
| 356 | /* Timing register sets */ |
|---|
| 357 | #define PD67_TIME_SETUP(n) (0x3a + 3*(n)) |
|---|
| 358 | #define PD67_TIME_CMD(n) (0x3b + 3*(n)) |
|---|
| 359 | #define PD67_TIME_RECOV(n) (0x3c + 3*(n)) |
|---|
| 360 | |
|---|
| 361 | /* Flags for PD67_MISC_CTL_1 */ |
|---|
| 362 | #define PD67_MC1_5V_DET 0x01 /* 5v detect */ |
|---|
| 363 | #define PD67_MC1_MEDIA_ENA 0x01 /* 6730: Multimedia enable */ |
|---|
| 364 | #define PD67_MC1_VCC_3V 0x02 /* 3.3v Vcc */ |
|---|
| 365 | #define PD67_MC1_PULSE_MGMT 0x04 |
|---|
| 366 | #define PD67_MC1_PULSE_IRQ 0x08 |
|---|
| 367 | #define PD67_MC1_SPKR_ENA 0x10 |
|---|
| 368 | #define PD67_MC1_INPACK_ENA 0x80 |
|---|
| 369 | |
|---|
| 370 | /* Flags for PD67_FIFO_CTL */ |
|---|
| 371 | #define PD67_FIFO_EMPTY 0x80 |
|---|
| 372 | |
|---|
| 373 | /* Flags for PD67_MISC_CTL_2 */ |
|---|
| 374 | #define PD67_MC2_FREQ_BYPASS 0x01 |
|---|
| 375 | #define PD67_MC2_DYNAMIC_MODE 0x02 |
|---|
| 376 | #define PD67_MC2_SUSPEND 0x04 |
|---|
| 377 | #define PD67_MC2_5V_CORE 0x08 |
|---|
| 378 | #define PD67_MC2_LED_ENA 0x10 /* IRQ 12 is LED enable */ |
|---|
| 379 | #define PD67_MC2_FAST_PCI 0x10 /* 6729: PCI bus > 25 MHz */ |
|---|
| 380 | #define PD67_MC2_3STATE_BIT7 0x20 /* Floppy change bit */ |
|---|
| 381 | #define PD67_MC2_DMA_MODE 0x40 |
|---|
| 382 | #define PD67_MC2_IRQ15_RI 0x80 /* IRQ 15 is ring enable */ |
|---|
| 383 | |
|---|
| 384 | /* Flags for PD67_CHIP_INFO */ |
|---|
| 385 | #define PD67_INFO_SLOTS 0x20 /* 0 = 1 slot, 1 = 2 slots */ |
|---|
| 386 | #define PD67_INFO_CHIP_ID 0xc0 |
|---|
| 387 | #define PD67_INFO_REV 0x1c |
|---|
| 388 | |
|---|
| 389 | /* Fields in PD67_TIME_* registers */ |
|---|
| 390 | #define PD67_TIME_SCALE 0xc0 |
|---|
| 391 | #define PD67_TIME_SCALE_1 0x00 |
|---|
| 392 | #define PD67_TIME_SCALE_16 0x40 |
|---|
| 393 | #define PD67_TIME_SCALE_256 0x80 |
|---|
| 394 | #define PD67_TIME_SCALE_4096 0xc0 |
|---|
| 395 | #define PD67_TIME_MULT 0x3f |
|---|
| 396 | |
|---|
| 397 | /* Fields in PD67_DMA_CTL */ |
|---|
| 398 | #define PD67_DMA_MODE 0xc0 |
|---|
| 399 | #define PD67_DMA_OFF 0x00 |
|---|
| 400 | #define PD67_DMA_DREQ_INPACK 0x40 |
|---|
| 401 | #define PD67_DMA_DREQ_WP 0x80 |
|---|
| 402 | #define PD67_DMA_DREQ_BVD2 0xc0 |
|---|
| 403 | #define PD67_DMA_PULLUP 0x20 /* Disable socket pullups? */ |
|---|
| 404 | |
|---|
| 405 | /* Fields in PD67_EXT_CTL_1 */ |
|---|
| 406 | #define PD67_EC1_VCC_PWR_LOCK 0x01 |
|---|
| 407 | #define PD67_EC1_AUTO_PWR_CLEAR 0x02 |
|---|
| 408 | #define PD67_EC1_LED_ENA 0x04 |
|---|
| 409 | #define PD67_EC1_INV_CARD_IRQ 0x08 |
|---|
| 410 | #define PD67_EC1_INV_MGMT_IRQ 0x10 |
|---|
| 411 | #define PD67_EC1_PULLUP_CTL 0x20 |
|---|
| 412 | |
|---|
| 413 | /* Fields in PD67_MISC_CTL_3 */ |
|---|
| 414 | #define PD67_MC3_IRQ_MASK 0x03 |
|---|
| 415 | #define PD67_MC3_IRQ_PCPCI 0x00 |
|---|
| 416 | #define PD67_MC3_IRQ_EXTERN 0x01 |
|---|
| 417 | #define PD67_MC3_IRQ_PCIWAY 0x02 |
|---|
| 418 | #define PD67_MC3_IRQ_PCI 0x03 |
|---|
| 419 | #define PD67_MC3_PWR_MASK 0x0c |
|---|
| 420 | #define PD67_MC3_PWR_SERIAL 0x00 |
|---|
| 421 | #define PD67_MC3_PWR_TI2202 0x08 |
|---|
| 422 | #define PD67_MC3_PWR_SMB 0x0c |
|---|
| 423 | |
|---|
| 424 | /* Register definitions for Cirrus PD6832 PCI-to-CardBus bridge */ |
|---|
| 425 | |
|---|
| 426 | /* PD6832 extension registers -- indexed in PD67_EXT_INDEX */ |
|---|
| 427 | #define PD68_EXT_CTL_2 0x0b |
|---|
| 428 | #define PD68_PCI_SPACE 0x22 |
|---|
| 429 | #define PD68_PCCARD_SPACE 0x23 |
|---|
| 430 | #define PD68_WINDOW_TYPE 0x24 |
|---|
| 431 | #define PD68_EXT_CSC 0x2e |
|---|
| 432 | #define PD68_MISC_CTL_4 0x2f |
|---|
| 433 | #define PD68_MISC_CTL_5 0x30 |
|---|
| 434 | #define PD68_MISC_CTL_6 0x31 |
|---|
| 435 | |
|---|
| 436 | /* Extra flags in PD67_MISC_CTL_3 */ |
|---|
| 437 | #define PD68_MC3_HW_SUSP 0x10 |
|---|
| 438 | #define PD68_MC3_MM_EXPAND 0x40 |
|---|
| 439 | #define PD68_MC3_MM_ARM 0x80 |
|---|
| 440 | |
|---|
| 441 | /* Bridge Control Register */ |
|---|
| 442 | #define PD6832_BCR_MGMT_IRQ_ENA 0x0800 |
|---|
| 443 | |
|---|
| 444 | /* Socket Number Register */ |
|---|
| 445 | #define PD6832_SOCKET_NUMBER 0x004c /* 8 bit */ |
|---|
| 446 | |
|---|
| 447 | #endif /* _LINUX_CIRRUS_H */ |
|---|
| 448 | |
|---|
| 449 | |
|---|
| 450 | |
|---|
